LDPE film grades: FD0270 vs FD0274 vs FD0474 vs 4025AS
Four LDPE grades with density 0.923–0.925 g/cm³, all for blown film. They differ mainly in melt flow (2.4 or 4) and in whether they contain slip and antiblock additives.
Articles on applications and grade selection for virgin plastic resins, based on producer TDS.
Four LDPE grades with density 0.923–0.925 g/cm³, all for blown film. They differ mainly in melt flow (2.4 or 4) and in whether they contain slip and antiblock additives.
LLDPE is the backbone of tough film, bags and laminates. The dart impact of these four grades differs by more than ten times – which decides how easily the film punctures.
H5604F and HD7000F are two popular Southeast Asian HDPE grades for thin film – carrier bags and HM film. Both have MI 0.04 and look very close on paper.
For injection HDPE, melt flow largely decides the application: low MFR for impact-resistant crates and pails, high MFR for caps and thin-walled containers. The table orders six grades from low to high MFR.
HDPE pipe comes in several kinds: pressure water pipe (PE100), cable conduit and general pipe. The five grades below belong to different groups – picking the wrong group is wrong from the start.
Large cans, drums and blown containers need slow-flowing HDPE that resists parison sag and stress cracking. For this group producers usually state melt flow at 21.6 kg (HLMI) instead of 2.16 kg.
Fishing nets, rope, woven-sack tape and tarpaulin use fiber-grade HDPE with melt flow around 1. The three grades below share that range but are aimed at slightly different products.
Spunbond nonwoven uses PP homopolymer with melt flow around 25–40. The seven grades below are all in this range and differ mainly in MFR and how much detail their TDS gives.
Low-flow PP impact copolymer (MFR 4–5) is used for large, thick injection parts that must take impact: crates, boxes, chairs and technical parts. The five grades below come from five producers.
Thin-wall food containers, cups and lids need very high-flow PP for fast filling and short cycles. The key choice is homopolymer (stiffer, clearer) or impact copolymer (tougher, better in the cold).
All four are injection-grade PP homopolymers with a melt flow of about 12 g/10 min, made by four different producers. Can they replace each other? The table compares them using each producer's TDS and highlights the differences that matter.
Five grades with the same melt flow of 9 g/10 min, all for impact-resistant injection parts. The difference lies in the balance between stiffness and impact toughness – which decides whether a part feels rigid or survives drops.
"5502" is a familiar name in bottle and jerry-can blow molding, and several producers sell a grade numbered 5502. This article compares three 5502 grades with HY55430 – a blow-molding grade in the same class from LyondellBasell – using each producer's TDS.
Random PP copolymer is used for clear injection parts: containers, cups, clear housewares. The three Korean grades below have melt flow of 29–40.
D-150 and DG417 are both medium-impact ABS for injection-molded housings, housewares and toys. One comes from Taiwan, the other from China – where do they differ?
Since late February 2026, the US–Iran conflict has disrupted the Strait of Hormuz – the main export route for Gulf oil and petrochemicals. This article summarizes events, explains why Asia's resin market was hit hard, and lists what Vietnamese plastics businesses should watch.
The Bab el-Mandeb strait links the Red Sea to the Indian Ocean – the gateway of the Suez route between Asia and Europe. Since late 2023, attacks by Yemen's Houthis have forced many carriers to sail around Africa. In 2026 the risk grew as the Houthis widened attacks against Saudi Arabia. This article looks at the impact on resin imported into Vietnam and on plastic goods exported to Europe.
When oil rises, resin prices usually follow – but not by the same percentage and not at the same time. This article traces the path from a barrel of crude to a bag of resin, explains why resin sometimes holds firm while oil falls, and lists the indicators buyers should watch.
In 2026, oil prices, freight and resin supply changed week by week because of conflict around Hormuz and the Red Sea. Here are 6 practical rules to keep production and cost stable without trying to time the top or bottom.
Y40L is a fiber-grade PP homopolymer from Dongguan Grand Resource with MFR 40 g/10 min, intended by the producer for spunbond nonwoven fabric. This article explains which layers of a diaper and a face mask Y40L is used for, why its properties fit, and what to check when choosing resin.
Message Thien An on Zalo, WhatsApp or WeChat: 0389 980 742
Or fill in the form and we will call you →