HDPE pipe grades: 100 Black vs XS10B vs XS10N vs M7100 vs IP1500WC
HDPE pipe comes in several kinds: pressure water pipe (PE100), cable conduit and general pipe. The five grades below belong to different groups – picking the wrong group is wrong from the start.
Updated: 17 Nov 2026 · Thien An Plastics
TDS comparison
| Property | 100 Black Tasnee | XS10B Hanwha TotalEnergies | XS10N Hanwha TotalEnergies | M7100 Lotte Chemical (Hivorex) | IP1500WC SK Geo Centric |
|---|---|---|---|---|---|
| Density | 0.959 g/cm³ | 0.959 g/cm³ | 0.948 g/cm³ | 0.95 g/cm³ | 1.025 g/cm³ |
| Melt flow (190 °C/5 kg) | 0.23 g/10 min | 0.3 g/10 min | 0.3 g/10 min | 0.25 g/10 min | — |
| Melt flow (190 °C/21.6 kg) | 6.4 g/10 min | — | — | — | — |
| Tensile strength at yield | 23 MPa | 26 MPa | 26 MPa | 230 kg/cm² (≈22.6 MPa) | 28 MPa |
| Tensile modulus | 900 MPa | — | — | — | — |
| Notched Charpy impact (23 °C) | 26 kJ/m² | — | — | — | — |
| Carbon black content | 2.25 % | — | — | — | — |
| Oxidation induction time OIT (210 °C) | 30 min | — | — | — | — |
| MRS rating | 10 MPa | — | — | — | — |
| Melting point | — | 129 °C | 129 °C | — | — |
| Elongation at break | — | ≥ 700 % | ≥ 700 % | — | — |
| Flexural modulus | — | 1100 MPa | 1100 MPa | — | 1000 MPa |
| Melt flow (190 °C/2.16 kg) | — | — | — | 0.06 g/10 min | 0.03 g/10 min |
| ESCR | — | — | — | > 1000 h | >1000 h |
| Vicat softening point | — | — | — | 125 °C | — |
Typical values from each producer's TDS, for reference only, not guaranteed specifications. "—" means not stated on the TDS. Values marked "≈" are unit conversions by Thien An for easier comparison.
Key differences
- 100 Black (Tasnee) states MRS 10 MPa (PE100), with 2.25 % carbon black and 30 min OIT – ready for black pressure pipe.
- XS10B and XS10N (Hanwha TotalEnergies) are bimodal PE100 grades per their producer; XS10B is black, XS10N natural (density 0.948) for your own colouring (e.g. blue stripes).
- M7100 (Lotte) and IP1500WC (SK) report ESCR above 1,000 h; IP1500WC is positioned for cable conduit and underground pipe (density 1.025 due to additives/fillers).
- Melt flow is measured at different loads (2.16, 5 and 21.6 kg), so values are not directly comparable.
Which grade to choose?
- Black pressure water pipe: 100 Black or XS10B.
- PE100 pipe needing your own colour: XS10N.
- Cable conduit, underground pipe: IP1500WC.
- General pipe without a PE100 requirement: consider M7100.
- Drinking-water pipe: also check certificates required by the project standard.
Tips when switching grades
- Compare like with like: same test method and units (ISO/ASTM; MPa or kg/cm²; Izod or Charpy). Values from different methods are not directly comparable.
- Melt flow has a lot-to-lot tolerance – check the COA of the actual lot, not just the TDS.
- Different additives (nucleating, antistatic, antioxidant, slip) can change the part even when key values match.
- Always trial on your own machine and mold: check temperature, pressure, shrinkage, colour and appearance before switching volume.
FAQ
What does PE100 mean?
PE100 is a pipe material class with a minimum required strength (MRS) of 10 MPa, used for pressure pipe such as water and gas.
Why are there black and natural PE100 grades?
Black grades contain carbon black for UV protection and are ready to use; natural grades let the plant add its own black or colour masterbatch.
Can IP1500WC be used for pressure water pipe?
Its producer positions it for cable conduit and underground pipe. For pressure pipe, use a PE100 grade with a stated MRS.
Grade pages with TDS downloads: 100 Black · XS10B · XS10N · M7100 · IP1500WC
Other comparisons: LDPE film grades · LLDPE film grades · HDPE film grades · HDPE injection grades by melt flow · HDPE for large blow-molded parts · HDPE for monofilament, nets and tape
Based on producers' public TDS, for technical reference only. For grade advice or a quote, contact Thien An Plastics: +84 389 980 742 (WhatsApp, WeChat, Zalo).