PP homopolymer for injection, MFR 12: 1100N vs J700N vs PH512 vs HJ500
All four are injection-grade PP homopolymers with a melt flow of about 12 g/10 min, made by four different producers. Can they replace each other? The table compares them using each producer's TDS and highlights the differences that matter.
Updated: 17 Nov 2026 · Thien An Plastics
TDS comparison
| Property | 1100N APC (Saudi Arabia) | J700N Hyosung (Korea) | PH512 PRefChem (Malaysia) | HJ500 Hanwha TotalEnergies (Korea) |
|---|---|---|---|---|
| Melt flow rate (230 °C/2.16 kg) | 12 g/10 min | 12 g/10 min | 12 g/10 min | 11 g/10 min |
| Density | 0.91 g/cm³ | 0.90 g/cm³ | 0.90 g/cm³ | 0.91 g/cm³ |
| Tensile strength at yield | 35 MPa | 360 kg/cm² (≈35 MPa) | 35 MPa | 380 kg/cm² (≈37 MPa) |
| Flexural modulus | — | 16,000 kg/cm² (≈1,570 MPa) | 1,475 MPa | 16,000 kg/cm² (≈1,570 MPa) |
| Notched Izod impact (23 °C) | — | 3.5 kg·cm/cm (≈34 J/m) | — | 3 kg·cm/cm (≈29 J/m) |
| Notched Charpy impact (23 °C) | 3 kJ/m² | — | — | — |
| HDT (0.45 MPa) | 85 °C | 110 °C | 95 °C | — |
| Vicat softening point | 154 °C | — | 153 °C | — |
| Rockwell hardness (R) | — | — | — | 100 |
Typical values from each producer's TDS, for reference only, not guaranteed specifications. "—" means not stated on the TDS. Values marked "≈" are unit conversions by Thien An for easier comparison.
Key differences
- Melt flow, density and tensile strength are almost identical, so for general-purpose injection parts the four grades can usually replace each other after a trial.
- The clearest difference is heat deflection temperature (HDT): 85 °C (1100N), 95 °C (PH512), 110 °C (J700N). Hyosung positions J700N as "high stiffness"; the flexural modulus of J700N and HJ500 (≈1,570 MPa) is also higher than PH512 (1,475 MPa).
- Impact values cannot be compared directly: 1100N reports Charpy (kJ/m²), J700N and HJ500 report Izod (kg·cm/cm) – different methods.
- Korean producers often use kg/cm²; convert to MPa (×0.098) before comparing.
Which grade to choose?
- Parts needing more stiffness and heat resistance (caps, components, housewares used with hot water): prefer J700N, then PH512.
- General-purpose injection parts where price and supply matter most: 1100N, PH512 and HJ500 all fit – choose by availability and current price.
Tips when switching grades
- Compare like with like: same test method and units (ISO/ASTM; MPa or kg/cm²; Izod or Charpy). Values from different methods are not directly comparable.
- Melt flow has a lot-to-lot tolerance – check the COA of the actual lot, not just the TDS.
- Different additives (nucleating, antistatic, antioxidant, slip) can change the part even when key values match.
- Always trial on your own machine and mold: check temperature, pressure, shrinkage, colour and appearance before switching volume.
FAQ
Can 1100N, J700N and PH512 replace each other?
For most general-purpose injection parts, yes – melt flow, density and tensile strength are almost the same. If the part needs heat resistance or high stiffness, run a trial, because HDT ranges from 85 °C to 110 °C.
Why do grades with the same MFR have different HDT?
Technology, additives and test practice differ between producers. Melt flow only describes processing flow, not stiffness or heat resistance.
Are TDS available for these grades?
Yes. Each grade page on thienanplastics.com has the TDS to download.
Grade pages with TDS downloads: 1100N · J700N · PH512 · HJ500
Other comparisons: PP impact copolymer for injection, MFR 9 · Are "5502" HDPE blow-molding grades from different producers the same? 5502 vs 5502BN vs Q5502BN vs HY55430 · Clear random PP for injection · General-purpose injection ABS
Based on producers' public TDS, for technical reference only. For grade advice or a quote, contact Thien An Plastics: +84 389 980 742 (WhatsApp, WeChat, Zalo).