PP for BOPP film: F3030 vs NSF113D vs UH622J vs UH625J vs 1104K
BOPP film (snack bags, labels, laminates, metallized film) uses PP homopolymer with MFR around 3. The five grades below – two made in Vietnam – have nearly the same MFR; they differ in stiffness, additives and the producer's target use.
Updated: 19 November 2026 · Thien An Plastics
Properties from the TDS
| Property | F3030 BSR – Binh Son (Vietnam) | NSF113D NSRP – Nghi Son (Vietnam) | UH622J Polymirae / Ulsan PP (Korea) | UH625J Polymirae / Ulsan PP (Korea) | 1104K APC (Saudi Arabia) |
|---|---|---|---|---|---|
| MFR (230 °C/2.16 kg) | 3.0 g/10 min | 3 g/10 min | 3 g/10 min | 3 g/10 min | 3.2 g/10 min (ISO 1133) |
| Density | — | 0.91 g/cm³ | 0.90 g/cm³ | 0.90 g/cm³ | 0.90 g/cm³ |
| Tensile strength at yield | 354 kgf/cm² (≈34.7 MPa) | 36 MPa | 370 kg/cm² (≈36.3 MPa) | — | 34 MPa (ISO 527-2) |
| Flexural modulus (* 1104K: tensile modulus, ISO) | 14,000 kgf/cm² (≈1,373 MPa) | 1,520 MPa | 16,000 kg/cm² (≈1,569 MPa) | — | 1,450 MPa * |
| Impact (23 °C) | Izod 2.1 kg·cm/cm (≈20.6 J/m) | Izod 39 J/m | Izod 4 kgf·cm/cm (≈39 J/m) | — | Charpy 4 kJ/m² |
| Vicat softening point | — | 155 °C | 146 °C | — | 154 °C |
| HDT (0.45 MPa) | — | 110 °C | 105 °C | — | 85 °C |
Typical values from each producer's TDS, for reference only and not specifications. "—" means not published in the TDS. Values marked "≈" were converted by Thien An for easier comparison.
Key differences
- All MFR ~3 – the standard range for BOPP core layers, so processing is similar.
- F3030 (Binh Son): TDS states no calcium stearate, no slip or antiblock, low water carry-over; runs well on high-speed lines and wide film; meets FDA 21 CFR 177.1520.
- UH622J has the highest flexural modulus in the table (≈1,569 MPa) and is aimed at metallizable film, cigarette film and high-speed lines; UH625J is the same producer's general BOPP grade.
- 1104K (APC, also H512M) contains no metal stearates or slip – suited to metallized film; data are ISO, so not directly comparable with the ASTM numbers.
- NSF113D (Nghi Son) lists HDT 110 °C and Vicat 155 °C – the highest published values here.
Which grade to choose?
- Locally made, fast delivery in Vietnam: F3030 or NSF113D.
- Metallized film, high stiffness: UH622J, 1104K, F3030 (no slip/antiblock).
- General BOPP film: UH625J, NSF113D.
Notes when switching grades
- BOPP skin/sealing layers normally use PP copolymer or terpolymer, not these homopolymers.
- Convert kg/cm² (Korean producers, Binh Son) to MPa by multiplying by 0.098.
- Trial on the line: check stretch ratio, thickness uniformity, clarity and ink/metal adhesion.
FAQ
Are F3030 and NSF113D interchangeable?
Both are Vietnamese BOPP homopolymers with MFR 3, so they are usually interchangeable after a line trial.
Which grade suits metallized BOPP?
UH622J and 1104K are aimed at metallized film; F3030 also has no calcium stearate, slip or antiblock.
Why can't 1104K be compared directly?
1104K publishes ISO data (tensile modulus, Charpy) while the others use ASTM (flexural modulus, Izod).
Is the TDS available?
Yes. Each grade page on thienanplastics.com has the TDS for download.
Grade pages (TDS download): F3030 · NSF113D · UH622J · UH625J · 1104K
More articles: PP homopolymer injection grades, MFR 12 · PP spunbond grades for nonwovens · How oil prices affect PP and PE resin prices
Based on producers' public TDS; for technical reference only. For grade advice or a quote, contact Thien An Plastics: +84 389 980 742 (WhatsApp, WeChat, Zalo).